Synchronous demodulation / detection

Today's radio receivers offer very high levels of performance and boast many facilities. Many radio receivers incorporate memories, phase locked loops, direct digital synthesis, digital signal processing and much more. One facility that can be very useful on the short wave bands is synchronous detection or synchronous demodulation as this can give much improved performance for receiving amplitude modulation (AM) transmissions. Unfortunately little is written about this form of modulation, and often it is a matter of accepting that it must be better than any normal options because it is included as a feature in the receiver specification.
Synchronous detection is used for the detection or demodulation of amplitude modulation (AM). This form of modulation is still widely used for broadcasting on the long, medium and short wave bands despite the fact that there are more efficient forms of modulation that can be used today. The main reason for its use nowadays is that it is very well established, and there are many millions of AM receivers around the world today.
In any receiver a key element is the detector. Its purpose is to remove the modulation from the carrier to give the audio frequency representation of the signal. This can be amplified by the audio amplifier ready to be converted into audible sound by headphones or a loudspeaker. Many receivers still use what is termed an envelope detector using a semiconductor diode for demodulating AM. These detectors have a number of disadvantages. The main one is that they are not particularly linear and distortion levels may be high. Additionally their noise performance is not particularly good at low signal levels.
These detectors also do not perform very well when the signal undergoes selective fading as often occurs on the short wave bands. An AM signal contains two sidebands and the carrier. For the signal to be demodulated correctly the carrier should be present at the required level. It can be seen that the signal covers a definite bandwidth, and the effects of fading may result in the carrier and possibly one of the sidebands being reduced in level. If this occurs then the received signal appears to be over-modulated with the result that distortion occurs in the demodulation process.

The spectrum of an amplitude modulated signal

Diode envelope detector

In virtually every receiver a simple diode envelope detector is used. These circuits have the advantage that they are very simple and give adequate performance in many applications.
The circuit of a typical detector is shown in Figure 2. Here the diode first rectifies the signal to leave only the positive or negative going side of the signal, and then a capacitor removes any of the remaining radio frequency components to leave the demodulated audio signal. Unfortunately diodes are not totally linear and this is the cause of the distortion.

An envelope detector for AM signals

What is synchronous demodulation

Signals can be demodulated using a system known as synchronous detection or demodulation. This is far superior to diode or envelope detection, but requires more circuitry. Here a signal on exactly the same frequency as the carrier is mixed with the incoming signal as shown in Figure 2. This has the effect of converting the frequency of the signal directly down to audio frequencies where the sidebands appear as the required audio signals in the audio frequency band.
The crucial part of the synchronous detector is in the production a local oscillator signal on exactly the same frequency as the carrier. Although it is possible to receive an AM signal without the local oscillator frequency on exactly the same frequency as the carrier this is the same as using the BFO in a receiver to resolve the signal. If the BFO is not exactly on the same frequency as the carrier then the resultant audio is not very good.

Synchronous demodulation Fortunately this is not too difficult to achieve and although there are a number of ways of achieving this the most commonly used method is to pass some of the signal into a high gain limiting amplifier. The gain of the amplifier is such that it limits, and thereby removing all the modulation. This leaves a signal consisting only of the carrier and this can be used as the local oscillator signal in the mixer as shown in Fig. 4. This is most convenient, cheapest and certainly the most elegant method of producing synchronous demodulation.

A synchronous detector using a high gain-limiting amplifier to extract the carrier

Advantages of synchronous detection

A synchronous detector is more expensive to make than an ordinary diode detector when discrete components are used, although with integrated circuits being found in many receivers today there is little or no noticeable cost associated with its use as the circuitry is often included as part of an overall receiver IC.
Synchronous detectors are used because they have several advantages over ordinary diode detectors. Firstly the level of distortion is less. This can be an advantage if a better level of quality is required but for many communications receivers this might not be a problem. Instead the main advantages lie in their ability to improve reception under adverse conditions, especially when selective fading occurs or when signal levels are low.
Under conditions when the carrier level is reduced by selective fading, the receiver is able to re-insert its own signal on the carrier frequency ensuring that the effects of selective fading are removed. As a result the effects of selective fading can be removed to greatly enhance reception.
The other advantage is an improved signal to noise ratio at low signal levels. As the demodulator is what is termed a coherent modulator it only sees the components of noise that are in phase with the local oscillator. Consequently the noise level is reduced and the signal to noise ratio is improved.
Unfortunately synchronous detectors are only used in a limited number of receivers because of their increased complexity. Where they are used a noticeable improvement in receiver performance is seen and when choosing a receiver that will be used for short wave broadcast reception it is worth considering whether a synchronous detector is one of the facilities that is required.


Luiggi Escalante
CI 18.878.611
CRF
Fuente:
http://www.radio-electronics.com/info/receivers/synchdet/sync_det.php

---